Build Your Own Gold Shaker Table with These Free Plans

Well, if yer lookin’ to build yourself a gold shaker table, let me tell ya, it ain’t as hard as it sounds. Ya just need a little patience and some elbow grease. I ain’t no expert, but I can tell ya how to get it done with some free plans I came across. They ain’t fancy, but they’ll work if yer after a way to separate gold from all them other little bits of rock and dirt ya been diggin’ up. Here’s a simple guide to build a gold shaker table right at home.

What You Need to Get Started

First off, you gotta gather some materials. I ain’t gonna lie, it’s gonna take a bit of work to get all the right stuff, but don’t worry, you can do it! You’ll need some wood or metal for the frame, a couple of motor parts, some rubber to make the table move, and a bit of grit for the surface. Don’t forget screws and bolts to hold everything in place!

Now, to get that thing to shake just right, you’ll need a small motor. Something like a 12-volt motor will do the trick, and a few belts to connect it all up. If ya can find an old washing machine motor or a fan motor, that’ll work great! Just make sure it’s strong enough to keep the table shaking properly. It don’t have to be the most expensive, just reliable enough to do the job.

Building the Frame

Start by makin’ the frame. Ya can make it outta wood or metal, whatever’s easier to get your hands on. The frame needs to be sturdy, ‘cause it’s gonna hold everything else up. It don’t have to be real big, just big enough for ya to spread out your dirt and rocks, and for the table to shake. Make sure it’s level, or else the whole thing won’t work like it should.

Once yer frame is built, lay down some kind of surface. If ya got some old steel sheets or even some thick plywood, it’ll do. Then, ya need to cut grooves into that surface. The grooves help the gold separate from the other junk. You don’t need to get fancy, just enough to let the gold slide down while the other stuff stays behind. You can use a saw or any other tool that can make them grooves nice and smooth.

Making the Table Shake

Now comes the fun part—making it shake! That’s the whole point of a shaker table, after all. The motor needs to be hooked up to the table somehow, and that’s where the belts come in. You want the motor to spin and move the table back and forth, but not too fast. Too much shake, and yer gold will be thrown off the table; too little, and it won’t work at all!

Once the motor’s hooked up and the table’s shaking, it’s time to test it out. Put a little dirt and rocks on the table and see how it goes. The heavy stuff, like gold, should slide down to the end, while the lighter stuff gets left behind. You’ll need to adjust the motor speed and the angle of the table, but once you get it right, it’ll work like a charm!

Testing and Tweaking

Don’t expect it to be perfect the first time. You gotta test it out a bit, and sometimes ya gotta make some changes. If it ain’t workin’ like ya thought, try adjusting the angle of the table or making the grooves a little deeper. It’s all about trial and error, just like everything else in life. Keep at it, and you’ll figure it out.

When ya got it right, you’ll see that gold start to collect at the bottom. It’s like magic, only it’s just a little bit of science and hard work! So if you’re serious about gettin’ that gold, this simple shaker table can save you a lot of time and effort.

Conclusion

So, there ya go, a simple and free plan for makin’ your own gold shaker table. You don’t need fancy tools or expensive parts—just some good old-fashioned know-how and a bit of work. If ya follow these steps, you’ll have yourself a table that’ll separate that gold from the dirt in no time!

Good luck with yer gold huntin’, and remember, keep on shakin’!

Tags：[Gold Shaker Table, DIY Shaker Table, Gold Recovery, Gold Prospecting, Build Your Own Shaker Table, Simple Shaker Table, Free Gold Shaker Plans]